Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Don't take too lightly the forklift at work. If the operation is not good, there will certainly be severe crashes in mins, and there are several accidents involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be located, causing a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and hangs on the roadside rack, which nearly triggers an mishap.
Case 4: Forklift is speeding and surrender throughout a turn.
Case 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the employees illegally, the forklift chauffeur does not wear the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not put on a seat belt and fell from the car when it rolled over and was squashed.
Forklift operation should take notice of these issues ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, beep the horn first and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be safe prior to starting.
3. When the forklift begins with a load, the motorist ought to initially confirm that the load is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole needs to be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, take care that there will certainly be no obstacles overhead. When the lots is traveling, the fork needs to not be elevated too high, which will certainly influence the stability of the forklift. .
3. After discharging, the fork must be decreased to the normal driving setting before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued initially. High-speed doglegs are banned. High-speed sharp turns will trigger the automobile to shed side stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the flame and slide, and it is forbidden to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and need to maintain a particular safety and security range from the lorry ahead. .
7. When the forklift is running, the load must be in the lowest position that does not hinder the driving, and the gantry ought to be appropriately slanted back. The lots will not be increased except when stacking or packing. .
8. The height of the load must not block the driver's view. In unique conditions, when the thing impacts the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to activate the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to stand on the fork to hold items and play a stabilizing duty. .
12. If issues are found, they will certainly be fixed and reported in a timely manner, and they will certainly never operate with ailments or conceal them.

filling and discharging.
1. When fork-loading items, the range in between the two forks need to be readjusted as needed to make the lots of the two forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is prohibited to collaborate with a single fork or utilize a fork top or pull. In unique scenarios, safety indication should be established to Stand-on Electric Pallet Stacker remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift must be stopped with the brake. .
4. The rate of the automobile should be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled items and hurt individuals. .
5. When making use of a fork to fork the goods, the fork should be as deep as feasible under the load, and it must be kept in mind that the fork suggestion need to not touch other products or objects. The tons needs to be stabilized with very little back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted onward slightly when the tons is decreased to allow for simple Stand-on Electric Pallet Stacker positioning of the tons and extraction of the forks. .
6. It is restricted to fork goods at high speed and ram tough objects with the fork head. .
7. When the forklift is working, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to participate in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to select, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the emergency brake manage to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the automobile's view and does not go beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be examined, and gas, lubing oil and air conditioning water must be added.
2. Check the safety efficiency of starting, running and stopping.
3. Check whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature level are regular.
5. After the forklift is running, the outside leakage should also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the propensity of " totally free switching";.
6. Running up and down the slope should be sluggish and uniform, and no turning on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is above 10%, the vehicle needs to be driven backwards when worsening;.
8. When the forklift workers lug the goods and progress, if they run into big or hefty products and most likely to the chauffeur's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not allowed to make use of inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844